0 of 0

File information

Last updated

Original upload

Created by

Dave Boss

Uploaded by

DaveBoss1

Virus scan

Safe to use

18 comments

  1. DaveBoss1
    DaveBoss1
    • premium
    • 1,377 posts
    • 69 kudos
    Locked
    Sticky
    If its not working, make sure to take the Fusion Core out and putit in again.
  2. ZxAsriel
    ZxAsriel
    • member
    • 75 posts
    • 0 kudos
    does this also make it so your AP in power armor is exceptional as well? Cause you run out of AP really fast when using the jetpack modification.
  3. blue35e
    blue35e
    • supporter
    • 6 posts
    • 0 kudos
    I tested the mod. even removing and replacing the fc I still had it drain. Slower than vanilla but something is still draining the core.
  4. bbt5926
    bbt5926
    • member
    • 1 posts
    • 0 kudos
    I have to re-enable the mod every time I start the game. I don't know enough about modding to say why that's the case or to figure out how to troubleshoot it. For those of you who are having trouble getting this mod to work, it might be because the mod isn't enabled. FYI, downloading and activating the mod via NMM does not equal enabling the mod. I had to go to the mods section from the main menu in-game, bring up the load order, and enable the mod from there. The mod works perfectly fine but re-enabling the mod every time I start the game is too much of an inconvenience for me, so I downloaded a different mod that does the same thing.
  5. Laidbackdnell
    Laidbackdnell
    • supporter
    • 6 posts
    • 0 kudos
    This mod does not work. I uninstalled and installed it multiple times using NMM and i've reloaded it numerous times the fusion core in concord still drains to 0
  6. HuntsInShadow
    HuntsInShadow
    • member
    • 47 posts
    • 1 kudos
    Does not work anymore.

    Testing done:

    Using the power armor from concord - the one near the minigun - & the partially drained fusion core from the basement of the building where the power armor can be found on the roof.

    Go into the power armor and sprinted around until the fusion core power level was approximately at the first line below 50%.

    Walked around most of the outer edge of sanctuary's build-able area carefully watching the power level of the fusion core in the armor.

    After a single loop the line hidden behind the arrow started to become visible - the drain felt slower then normal but not unlimited.

    The fusion cell was not left in the armor (to prevent settlers wandering off with the power armor) and was placed in after loading a save that did not have a fusion core installed.

    I noticed a similar problem with a mod I downloaded a while ago that did the same thing and it worked initially but then stopped working, maybe because of a bit of code added by bethesda during an update that unintentionaly breaks these type of mods.
    1. DaveBoss1
      DaveBoss1
      • premium
      • 1,377 posts
      • 69 kudos
      It works, I have it since a year installed and it still does what it does. You either have a mod conflict or something overwriting it. This mod sets the drain value to 0, nothing a Bethesda code could change since they're not patching this game for almost 2 years. I can tell you for sure this mod works.

      Note: Did you looked into your mod manager in the plugin section if the file is active?
    2. HuntsInShadow
      HuntsInShadow
      • member
      • 47 posts
      • 1 kudos
      Installed the mods manualy.

      File is active.

      I have all the official DLC as far as I can tell (the HQ textures is disabled however) and the only mods installed & active (aside from this one) is An alternate start mod 'start me up' & two additional quest mods 'Maxwell's World' & 'Northern Springs'.

      I have the mod active during testing but currently have it removed.

      Any ideas ?
    3. mjrcooke
      mjrcooke
      • member
      • 1 posts
      • 0 kudos
      have the same problem. Installed it via NMM, doesn't work.
      Did you manage to fix the issue?
    4. Laidbackdnell
      Laidbackdnell
      • supporter
      • 6 posts
      • 0 kudos
      This mod does not work. I uninstalled and installed it multiple times using NMM and i've reloaded it numerous times the fusion core in concord still drains to 0
  7. JonnyMashT
    JonnyMashT
    • member
    • 13 posts
    • 0 kudos
    Yeah, it's not working. I even take the Fusion Core out and put it back in, it does not say 100%.
    1. JonnyMashT
      JonnyMashT
      • member
      • 13 posts
      • 0 kudos
      Nevermind, I check the plugins, and it did not have the check mark. Now it is working.
  8. esanti21
    esanti21
    • premium
    • 12 posts
    • 0 kudos
    Hi, I've tried your mod (today), but it does not work. I do not use any other modes, so there can be no compatibility issue. It is possible that this works only with newly acquired fusion cores?? (sorry for bad english....)
    1. DaveBoss1
      DaveBoss1
      • premium
      • 1,377 posts
      • 69 kudos
      It works with every fusion core
  9. CheeseBurger47
    CheeseBurger47
    • member
    • 34 posts
    • 0 kudos
    make unlimited jetpack boost pls
  10. GlennCroft
    GlennCroft
    • member
    • 601 posts
    • 11 kudos
    >it gets sucked out like a Virgin by a Vampire
    1. DaveBoss1
      DaveBoss1
      • premium
      • 1,377 posts
      • 69 kudos
      Vampires do love Virgin blood
  11. TheMrFoster
    TheMrFoster
    • member
    • 24 posts
    • 0 kudos
    nice, an esl version
Top